The Silver Bullet Colloidal Generator
Part List
1. 120 Volt AC to 48 Volt DC Generator
2. 120 Volt AC Timer
3. 1 Quart Glass Jar
4. Generator Mounting Board
5. Two Silver Electrodes w/ Rubber Holder
6. 8 oz. Bottle
7. 2 oz. Bottle w/ Dropper
The
Silver Bullet Colloidal Generator is powered by 120 volts AC with an
output of 48 volts DC and never requires batteries. This unit makes a
colloidal product that with longer cook times can have a high particle
content and works very efficiently with silver or copper electrodes.
This
is the most effective colloidal silver generator on the market for a
price under $100.00. It is simple to use without unnecessary bells and
whistles and produces some of the best combination ionic and particle
silver colloids by a non-commercial generator unit.
Although the Home Generators on this page can produce very effective colloids,if you require a more therapeutic internal use, it may be necessary to use a higher particle silver such as our Advanced Colloidal Silver. If you have purchased this home unit, but occasionally want to use our Advanced Colloidal Silver it will be made available to you at anytime with a buy one 8 oz. bottle at the regular retail price and get one free. Simply call in and give your name for the order clerk to look up in the generator orders database. This offer available by call in only at 830 966-2315.
Instructions:
- Fill the 1
quart glass jar to the shoulder with distilled water. Use the TDS1 tester to be
sure the PPM reading of the distilled water is at 1 or less.
- Insert the
two electrodes into the board holes allowing 1/8” to stick above the green
rubber electrode holders and place the assembly board onto the glass jar. (Be
sure that the electrodes do not touch each other after the unit is plugged in.)
- Attach the
generator onto the board matching the Velcro and plug the 120 volt power cord
into the generator and then into the timer.
- Attach the
black and red alligator clips from the generator to the bare metal of the
electrodes protruding from the green rubber holders. (These alligator clips are
your 48 volt DC output.)
- This step
can be skipped unless you desire to change the timer settings, which are already
set according to the following instructions. (Note: It is not necessary to set
the real time of day. To get started after setting your pins for the start and
stop cycles, just rotate your first green pin to a position just to the left of
the roller actuator switch which is on the top left hand side of the
timer.)
- Use a green
pin to set the first start time.
- Use a red
pin to set the first stop time at about 1-1/2 hour later.
- Use a green
pin to set the second start time at ˝ hour later to allow a cool down period.
This will extend the life of your generator. (During this cool down time, wipe
the silver oxide from the electrodes and switch the red and the black electrode
clips. This will ensure that the two electrodes both wear down somewhat
uniformly.)
- Use a red
pin to set the second stop time.
- Check to be
sure that the first green pin is in a position just to the left of the roller
actuator switch which is on the top left hand side of the
timer.
- Last, plug
the timer into a 110-120 volt outlet and turn the timer on using the roller
actuator switch.
If
you desire a stronger PPM and higher particle content, simply rotate
the setting pins around just to the left side of the roller actuator
switch and restart the process.
Note: Ionic content will
register on the TDS1 meter, but particle content will not. Particle
content will be evidenced by its color since particles reflect light
and ions do not.
This 120 volt AC to 48 volt DC
process makes an ionic product with a good dispersal of both ionic and silver
particles For more info about ionic silver vs. particle silver, go to, http://www.utopiasilver.com/faq/ionic-non-ionic.htm;
http://www.utopiasilver.com/faq/particle-size.htm
This product was added to our catalog on Wednesday 29 October, 2008.
